- B2B
- Growth StageExpanding market presence
Electronics Assembly Technician
- ₹3.5L – ₹4.5L
- |
- |2 years of exp
- |Full Time
In office
Not Available

About the job
**Job description:
Position: Electronics Assembly Technician
Openings: 1
Experience: 2–5 Years
Location: Bangalore
Employment Type: Full-time
About the role
Ipsator designs and builds connected hardware, and our EMS line assembles boards, cable sets and finished units for our own products and for customers. Much of that work cannot go through a machine: through-hole parts, fine-pitch headers, board-to-wire terminations, and custom cable sets all depend on a steady, trained pair of hands.
We are hiring a technician who takes pride in clean, repeatable joints. You will sit at the bench every day, building and reworking assemblies to drawing, and your work will go straight into products that ship. This is a hands-on production role, not a supervisory one.
What you'll do
Board-level hand assembly
Hand-solder through-hole and surface-mount parts onto printed circuit boards,
including pin headers, connectors, switches, sensors, modules and discrete components.Work confidently at fine pitch, down to 1.27 mm (50 mil) lead spacing, without bridging, lifted pads or overheated parts.
Terminate flying leads and cable ends directly onto board pads and plated holes, with proper strain relief.
Carry out rework and repair: remove and replace parts, clear bridges, touch up dry or cold joints, and fit modification wires where an engineering change calls for it.
**Cable and harness building
Cut, strip and tin wire to the lengths and gauges specified, from 2.5 sq mm power cable down to 30 AWG signal wire.
Crimp terminals for small-format connector families such as JST (SH, GH, PH, XH), Molex and Dupont-style housings, using the correct hand tool or applicator for each terminal; fit lugs and bootlace ferrules on heavier conductors up to 2.5 sq mm.
Make inline wire-to-wire connections by splicing, soldering or crimping (butt and ferrule types), then insulate them with heat-shrink sleeving.
Load housings in the right pin order, then bundle, sleeve, tie and label finished harnesses as per the drawing
Quality and inspection
Inspect your own work under a magnifier or microscope before it leaves the bench.
Run continuity and pull checks on crimps and harnesses, and basic multimeter checks on assembled boards.
Build to assembly drawings, wiring diagrams, BOMs and work instructions; raise a query when a document is unclear instead of guessing.
Record defects and rework on the job traveller so recurring issues can be traced and fixed.
Bench and tool care
Follow ESD precautions at all times: wrist strap, mat, and correct handling and packing of sensitive parts.
Maintain soldering stations, tips, hot-air tools, crimpers and strippers; flag worn tooling before it affects quality.
Keep the workstation clean and organised, with solder, flux, wire and terminals correctly stored and accounted for.
Meet daily output targets while holding the quality standard.
Required
ITI or Diploma in Electronics, Electrical or a related trade; equivalent shop-floor experience is equally welcome.
2–5 years of daily hand-soldering work in an EMS unit, cable harness shop, or electronics production or repair facility.
Proven ability to solder at 1.27 mm pitch, on both through-hole and surface-mount parts.
Practical experience crimping small signal terminals and assembling multi-way connector housings, and terminating heavier power wiring with lugs and ferrules
Able to read assembly drawings, wiring diagrams and a BOM, and identify components and their polarity.
Comfortable with a temperature-controlled soldering station, hot-air tool, flux, desoldering wick and pump, wire strippers and a multimeter.
Good eyesight for close work, a steady hand, and the patience to do the same job correctly the hundredth time.
Working knowledge of ESD handling.
Able to follow written work instructions in English; Kannada or Hindi for day-to-day communication.
Shortlisted candidates will take a practical bench test covering fine-pitch soldering and terminal crimping.
Nice to have
IPC-A-610 or J-STD-001 training or certification, or IPC/WHMA-A-620 for cable work.
Hot-air rework of fine-pitch ICs, QFN packages and 0402-size passives.
Regular work under a stereo microscope.
Experience with lead-free (RoHS) solder as well as leaded.
Exposure to conformal coating, potting or adhesive application.
Basic functional testing or firmware flashing of assembled boards using a test jig.
Experience training or guiding junior operators.
About the company
Ipsator is a Bengaluru-based technology company that designs and builds connected
hardware, including the EyEagle and Resonara products. Design, firmware and manufacturing sit under one roof, so the people who build the product work alongside the engineers who designed it.
Benefits:
Flexible schedule
Food provided
Health insurance
Paid sick time
Paid time off
Provident Fund
About the company
- B2B
- Growth StageExpanding market presence
Employees joined from

Perks
Founders
Similar Jobs




